Door pocket is an architectural decoration term, which refers to the two door frames inside and outside the door. It is also directly called door frame. Its main function is to fix the door leaf, protect the wall corner and decoration. It is often used in the decoration process to protect the door from scratch, corrosion, damage and dirt.

如為前一種方法——現場制作的不銹鋼門套由現場裝修工人用釘子直接固定在門洞墻上；如果安裝了整套門產品的不銹鋼門套，則應考慮兩個問題：

If it is the former method - the stainless steel door pocket made on site is directly fixed on the door opening wall by the on-site decoration workers with nails; If a stainless steel door pocket of a complete set of door products is installed, two issues should be considered:

一是相應成套門產品的不銹鋼門套的技術結構是否滿足成套門產品所需的牢固、準確、穩定三大技術特征；

First, whether the technical structure of the stainless steel door pocket of the corresponding complete set of door products meets the three technical characteristics of firmness, accuracy and stability required by the complete set of door products;

二是整套門的安裝人員應在安裝現場進行事先調查，并規范安裝過程中的工藝流程（如使用發泡劑可能會對不銹鋼門的牢固性、準確性和未來使用穩定性產生所有可能的影響）。

Second, the installation personnel of the whole set of doors shall conduct a prior investigation at the installation site and standardize the process flow in the installation process (if foaming agent is used, it may have all possible effects on the firmness, accuracy and future use stability of stainless steel doors).

1.根據設計圖紙檢查門的規格、開啟方向及相關附件。

1. Check the specification, opening direction and relevant accessories of the door according to the design drawings.

2.用卷尺測量車門開口的高度和寬度。門的標準高度和寬度為200cm×80cm；衛生間門高寬為200cm×70cm，如有尺寸偏差應及時糾正。

2. Measure the height and width of the door opening with a tape measure. The standard height and width of the door is 200cm × 80cm； The height and width of toilet door is 200cm × 70cm. Any dimensional deviation shall be corrected in time.

3.測量位置線，確定門框的位置，用噴墨器拉出垂直線，并在一側拉出門洞的兩條垂直線。

3. Measure the position line, determine the position of the door frame, pull out the vertical line with an inkjet, and pull out two vertical lines of the door opening on one side.

4.用沖擊鉆在垂直線上鉆孔。兩個孔之間的距離約為30厘米。一扇側門的兩排上有10個孔。沖擊鉆的鉆頭應為12mm，鉆孔深約為6cm。

4. Use percussion drill to drill holes on the vertical line. The distance between the two holes is about 30 cm. There are 10 holes in the two rows of a side door. The bit of percussion drill shall be 12mm and the drilling depth shall be about 6cm.

5.將小木楔逐個錘入孔中，固定門框板。小木楔的體積為5cm×1.5cm×1.5cm，用落葉松制作更好，因為落葉松的木材結構緊密，不易松動。

5. Hammer the small wooden wedges into the holes one by one to fix the door frame plate. The volume of the small wooden wedge is 5cm × 1.5cm × 1.5cm, it is better to make it with Larch, because the wood structure of larch is compact and not easy to loosen.

6.切割材料制成門框。制作左右兩側門框龍骨的木工板尺寸為200cm×3cm×8cm，門框頂部龍骨的木工板尺寸為80cm×3cm×8cm，將高密度9cm板粘在龍骨上，用氣槍釘固定。

6. Cut materials to make door frames. The dimension of the woodworking board for making the keel of the door frame on the left and right sides is 200cm × 3cm × 8cm, the dimension of the woodworking board of the keel on the top of the door frame is 80cm × 3cm × 8cm, stick the high-density 9cm board on the keel and fix it with air gun nail.

7.根據門的形狀連接三個裝配好的門框，并用大釘子將其固定在接縫處。

7. Connect three assembled door frames according to the shape of the door and fix them at the joint with large nails.

8.使用平面使連接的門框表面光滑，并用清晰的棱角修剪棱角。

8. Use a plane to make the surface of the connected door frame smooth, and trim the edges with clear edges and corners.

9將門框放在門洞上，以墻面水平線為準，在門框下墊木或磚，調整門框高度。預留5cm，埋入地板龍骨內。

9 place the door frame on the door opening, subject to the horizontal line of the wall, pad wood or brick under the door frame, and adjust the height of the door frame. Reserve 5cm and bury it in the floor keel.

10在門框上釘一顆釘子，垂直掛線，通過線垂調整門框的垂直度，用扭釘將門框測量固定在門洞上。

10 nail a nail on the door frame, hang the line vertically, adjust the verticality of the door frame through the line verticality, and measure and fix the door frame on the door opening with twist nails.

11在門的正面畫線。門面可從貨架上購買或由施工人員根據圖紙制作。制作完成后，將門面固定在門框上，使不銹鋼門套基本完成。

11 draw a line on the front of the door. The facade can be purchased from the shelf or made by the construction personnel according to the drawings. After fabrication, fix the door surface on the door frame to basically complete the stainless steel door pocket.

12將門放在不銹鋼門套上，畫出，確定鉸鏈在不銹鋼門套上的具體位置，然后根據鉸鏈的厚度切割口徑。同時切掉鎖套的直徑。將門安裝在不銹鋼門套上，并用鉸鏈上的鑼和鋼絲刀擰緊鑼和螺釘。注意門與不銹鋼門套之間的間隙不大于1.5mm，以門的順利開關為準。

12 place the door on the stainless steel door pocket, draw, determine the specific position of the hinge on the stainless steel door pocket, and then cut the caliber according to the thickness of the hinge. At the same time, cut off the diameter of the lock sleeve. Install the door on the stainless steel door pocket, and tighten the gong and screw with the gong and wire knife on the hinge. Note that the gap between the door and the stainless steel door pocket shall not be greater than 1.5mm, subject to the smooth opening and closing of the door.

以上就是為大家介紹的有關電梯門套線的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.n5671.cn

The above is the detailed introduction of elevator door pocket line. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://www.n5671.cn