調整不銹鋼玻璃門通常涉及以下幾個步驟：

　　Adjusting stainless steel glass doors usually involves the following steps:

　　檢查螺絲緊固情況 ：

　　Check the tightness of screws:

　　打開不銹鋼面板，檢查地彈簧內部的調節螺絲和玻璃門夾的螺絲是否松動。

　　Open the stainless steel panel and check if the adjustment screws inside the floor spring and the screws of the glass door clamp are loose.

　　如果發現螺絲松動，使用螺絲刀逆時針擰緊。

　　If the screws are found to be loose, use a screwdriver to tighten them counterclockwise.

　　調整玻璃門速度 ：

　　Adjust the speed of the glass door:

　　找到地彈簧上的調節螺絲，使用一字改錐（或類似工具）進行微調。

　　Find the adjustment screw on the ground spring and use a flat screwdriver (or similar tool) for fine adjustment.

　　逆時針擰松第1顆和第2顆螺絲來調整玻璃門的關門速度。

　　Loosen the first and second screws counterclockwise to adjust the closing speed of the glass door.

　　注意調整幅度要小，避免滑絲或螺絲脫落。

　　Pay attention to the small adjustment range to avoid slipping or screw detachment.

　　調整玻璃門高低 ：

　　Adjust the height of the glass door:

　　調整地彈簧上面的不銹鋼面板的螺絲，以改變地彈簧的高度，從而調整玻璃門的高度。

　　Adjust the screws on the stainless steel panel above the floor spring to change the height of the floor spring, thereby adjusting the height of the glass door.

　　如果玻璃門有下沉現象，可能需要調整地彈簧本體或玻璃門夾的位置。

　　If the glass door sinks, it may be necessary to adjust the position of the ground spring body or glass door clamp.

　　調整玻璃門縫隙 ：

　　Adjust the gap of the glass door:

　　調整玻璃門縫隙通常通過調整鉸鏈處的螺絲來實現。

　　Adjusting the gap of glass doors is usually achieved by adjusting the screws at the hinges.

　　順時針旋轉螺絲可以增大縫隙，逆時針旋轉可以減小縫隙。

　　Clockwise rotation of the screw can increase the gap, while counterclockwise rotation can decrease the gap.

　　調整后，確保門的開關正常，縫隙均勻平整。

　　After adjustment, ensure that the door switch is normal and the gap is even and smooth.

　　測試調整效果 ：

　　Test adjustment effect:

　　在每次調整后，都要測試玻璃門的開關情況，確保運行順暢，縫隙合適。

　　After each adjustment, the opening and closing of the glass door should be tested to ensure smooth operation and appropriate gaps.

　　如果玻璃門有交叉相撞的問題，可能需要調整上夾或下夾的位置，并確保所有螺絲擰緊。

　　If there is a cross collision issue with the glass door, it may be necessary to adjust the position of the upper or lower clamp and ensure that all screws are tightened.

　　請根據具體情況微調，并確保在調整過程中注意安全。如果遇到困難或不確定如何操作，建議聯系專業人士進行幫助

　　Please adjust according to the specific situation and ensure safety is taken into account during the adjustment process. If encountering difficulties or unsure how to operate, it is recommended to contact professionals for assistance

　　本文由山東不銹鋼玻璃門提供技術支持，更多的詳細精彩內容請點擊我們的網站http://www.n5671.cn，我們將會全心全意為您提供滿意的服務。

　　This article is supported by Shandong Stainless Steel Glass Doors. For more detailed and exciting content, please click on our website http://www.n5671.cn We will wholeheartedly provide you with satisfactory service.